What to know about R-1233zd(E) chillers
R-1233zd(E) is one of many refrigerant designations that can appear in chiller information. The exact suffix matters: transcribe the complete label and do not shorten it when requesting a quote.
We consider chillers using all refrigerants, including equipment labeled R-1233zd(E). A refrigerant label is only one part of the offer: the complete machine, its condition, included components and the pickup route also matter. Do not infer the current charge from a model name.
Plan the pickup at your Ohio site
Ohio pickup planning starts at the exact equipment location, not just the mailing address. Show the machine in its room or on its pad, the intended exit, the route to a truck and any locked gates. Tell us who can approve access and whether nearby equipment needs to stay in service. A roof, basement and outdoor yard each present different handling questions.
Tell us about known site restrictions before scheduling. A site contact can explain what is accessible, but the removal team must evaluate the actual route, load and work area.
Define the asset at its boundaries
Include the full refrigerant designation, model, serial number and photographs of the current label and any service markings.
A chiller purchase is clearer when the owner identifies the machine, any matching starter or drive, and the controls that go with it. Photograph the complete assembly as well as its manufacturer, model, serial, capacity, voltage and refrigerant label. Note which pumps, tower, pipes and building controls must stay. A brand name on nearby equipment is not a substitute for a unit-level identification.
Condition is information, not a testing requirement
Disclose any known leak, prior recovery or conversion. The actual charge can be unknown; do not restart the chiller or open a fitting to find out.
A machine described as spare may be disconnected, or it may still be connected and held for backup. Clarify its current release status and when the site can make it available; do not start it just to establish its value.
We consider used, surplus and non-running chillers, including equipment of unknown operating condition. There is no need to restore power, repair a fault or perform a performance test to ask for a cash offer. Accurate disclosure and a possible site access review are different from requiring the machine to operate.
Separate the chiller from live plant systems
The buyer coordinates and pays for the agreed disconnects and refrigerant recovery. Before the chiller is released, the facility representative should identify which water circuits, electrical feeds and controls serve other equipment. Qualified personnel plan isolation and recovery for the actual system. A machine that is not running can still contain refrigerant, fluid or stored electrical energy; do not cut, drain or vent it to obtain an offer.
Measure the path from room to truck
Tell the buyer whether a recovery record exists; an installed charge and the machine’s removal access must be assessed independently.
The buyer covers agreed rigging, crane work if needed, loading, freight and hauling. Give the width and height of the narrowest opening, the distance to the loading point and any turns or changes of level. The chiller may have been installed before walls, cables or other equipment were added. A rigging crew verifies actual weight, lifting points and floor capacity; the owner should not try to move the machine for a quote.
Confirm ownership before release
An equipment owner, tenant and building owner may not be the same party. Identify who can authorize the sale and who can grant site access, including any financing or lease questions that need to be resolved. We offer cash and pay upfront before pickup after acceptance. The written scope should identify the chiller and the disconnect, recovery, rigging and freight work the buyer will cover.
For a closure, identify a primary contact who can provide access and answer questions after operations stop. Ask whether there are other contractors working in the same space or using the same loading area.
What to send for a useful first conversation
For a central plant, mark the chiller being offered in a wide photograph and identify the starter or drive if it is elsewhere. Provide the model, serial, tonnage and refrigerant if known. Describe connected systems that remain in service, the likely exit and the facility contact who can review isolation and access.
For a chiller marked R-1233zd(E) in Ohio, include the location and a contact who can confirm the asset and arrange site access. If a detail is unavailable, say so instead of taking an unsafe photograph or guessing at the specifications.
Can several chillers be offered together?
Yes. List each machine, its model, serial, condition and location, and state whether it is part of a group transaction. Similar-looking units may have different refrigerants, included drives or access requirements. No testing is required for an offer.
