What to know about used industrial chillers
A surplus chiller can be a single packaged machine or part of a larger central cooling plant. The most useful starting point is not an estimate of scrap weight, but an inventory of the specific equipment offered and the practical route out of the building.
Owners in Madison County can request an offer for one surplus machine or several separately identified units. The actual model, current condition and pickup access matter more than whether the equipment is in a city, an industrial property or an outlying facility. Identify the owner and the machine before assuming adjacent pumps or other assets are part of the sale.
Plan the pickup at your Madison County site
For pickup in Madison County, provide the actual site address and service entrance, whether the equipment is in London, the county seat, or elsewhere in the county. The address alone does not show where a truck can stage or where the chiller exits. Where the chiller is above ground level, note how it can be reached and whether the roof edge, walls or nearby equipment limit a lift. Share available drawings, but let a qualified crew verify loading and reach.
Tell us about known site restrictions before scheduling. A site contact can explain what is accessible, but the removal team must evaluate the actual route, load and work area.
Define the asset at its boundaries
Photograph the whole assembly and its manufacturer label, and note whether a starter, drive or control cabinet is attached or separate.
A chiller purchase is clearer when the owner identifies the machine, any matching starter or drive, and the controls that go with it. Photograph the complete assembly as well as its manufacturer, model, serial, capacity, voltage and refrigerant label. Note which pumps, tower, pipes and building controls must stay. A brand name on nearby equipment is not a substitute for a unit-level identification.
Condition is information, not a testing requirement
Equipment can be shut down, older, incomplete or of unknown operating status; explain what you know without restarting it.
If a prior operator’s records cannot be located, provide the information currently visible and say what is unknown. We can discuss an offer without a performance demonstration, although the equipment and access still need to be identified.
We consider used, surplus and non-running chillers, including equipment of unknown operating condition. There is no need to restore power, repair a fault or perform a performance test to ask for a cash offer. Accurate disclosure and a possible site access review are different from requiring the machine to operate.
Keep an occupied building operating
If the property remains occupied, tell the buyer which cooling services and access routes must remain available. A facility representative should establish the work boundaries before qualified personnel plan the actual disconnect and refrigerant recovery. We coordinate and pay for that work within the agreed purchase scope. The owner does not need to vent, drain or isolate the chiller to request a cash offer.
Measure the path from room to truck
For indoor equipment, identify the corridor, doorway and proposed loading area; for outdoor equipment, show the pad, fence and truck approach.
The buyer covers agreed rigging, crane work if needed, loading, freight and hauling. Give the width and height of the narrowest opening, the distance to the loading point and any turns or changes of level. The chiller may have been installed before walls, cables or other equipment were added. A rigging crew verifies actual weight, lifting points and floor capacity; the owner should not try to move the machine for a quote.
Confirm ownership before release
An equipment owner, tenant and building owner may not be the same party. Identify who can authorize the sale and who can grant site access, including any financing or lease questions that need to be resolved. We offer cash and pay upfront before pickup after acceptance. The written scope should identify the chiller and the disconnect, recovery, rigging and freight work the buyer will cover.
Where records conflict, share both the installed equipment label and the inventory sheet. The buyer can resolve questions during review rather than assuming that a single old schedule describes the present machine.
What to send for a useful first conversation
Start with an asset list: manufacturer, model, serial, rated capacity, refrigerant and the location of each machine. Identify which units are surplus and whether they are still connected. Add photographs showing the room, pad or roof and the route toward a loading area. If the records are incomplete, mark unknown items rather than guessing or starting the machine.
For used chillers in Madison County, include the location and a contact who can confirm the asset and arrange site access. If a detail is unavailable, say so instead of taking an unsafe photograph or guessing at the specifications.
Can a non-running machine be sold?
Yes. We consider non-running and unknown-condition equipment, and do not require a performance test. Describe known defects and missing parts so an offer can reflect the machine as it sits. Site access and safe removal still need to be evaluated.
