What to know about Smardt chillers
Some Smardt chillers use oil-free magnetic-bearing compressor technology, but the name alone is not proof of a particular configuration. Explain the installed compressor type where known and provide the machine label so the actual equipment can be evaluated.
A nameplate-led quote begins with a legible photo of the actual chiller, not a generic brochure. Add a wide shot, its exact location and any separate starter or drive. If the tag cannot be read, the model on an asset list and photographs may still provide a starting point.
Plan the pickup at your Ohio site
Ohio pickup planning starts at the exact equipment location, not just the mailing address. Show the machine in its room or on its pad, the intended exit, the route to a truck and any locked gates. Tell us who can approve access and whether nearby equipment needs to stay in service. A roof, basement and outdoor yard each present different handling questions.
Tell us about known site restrictions before scheduling. A site contact can explain what is accessible, but the removal team must evaluate the actual route, load and work area.
Define the asset at its boundaries
Photograph the complete unit, its model and serial label, individual compressor labels if safely visible, and the controller or separate power cabinet.
A chiller purchase is clearer when the owner identifies the machine, any matching starter or drive, and the controls that go with it. Photograph the complete assembly as well as its manufacturer, model, serial, capacity, voltage and refrigerant label. Note which pumps, tower, pipes and building controls must stay. A brand name on nearby equipment is not a substitute for a unit-level identification.
Condition is information, not a testing requirement
Mention disconnected controls, a compressor issue or service history only if known. An unknown fault does not require a test or an attempt to reset the machine.
If a prior operator’s records cannot be located, provide the information currently visible and say what is unknown. We can discuss an offer without a performance demonstration, although the equipment and access still need to be identified.
We consider used, surplus and non-running chillers, including equipment of unknown operating condition. There is no need to restore power, repair a fault or perform a performance test to ask for a cash offer. Accurate disclosure and a possible site access review are different from requiring the machine to operate.
Separate the chiller from live plant systems
The buyer coordinates and pays for the agreed disconnects and refrigerant recovery. Before the chiller is released, the facility representative should identify which water circuits, electrical feeds and controls serve other equipment. Qualified personnel plan isolation and recovery for the actual system. A machine that is not running can still contain refrigerant, fluid or stored electrical energy; do not cut, drain or vent it to obtain an offer.
Use drawings without treating them as a lift plan
Identify the heat exchangers, compressor mounting and power connections in photographs; the removal crew will determine safe lifting points and handling.
Existing dimensions, rigging drawings or documented weights can help frame the job, especially for a large central-plant unit. Tell us whether they describe the installed configuration or an earlier one. The buyer covers agreed rigging, crane if needed, loading, freight and hauling. The crew still verifies current obstacles, floor capacity, actual weight and lifting points before moving the equipment.
Document an as-is purchase
A clear as-is discussion distinguishes known faults from missing information. Provide photographs and describe removed components or an uncertain history; a running test is not required. We consider those facts alongside the removal requirements when making a cash offer. If accepted, payment is upfront before pickup. Confirm the machine, included accessories and buyer-paid scope rather than relying on an informal verbal description.
For a closure, identify a primary contact who can provide access and answer questions after operations stop. Ask whether there are other contractors working in the same space or using the same loading area.
What to send for a useful first conversation
For a central plant, mark the chiller being offered in a wide photograph and identify the starter or drive if it is elsewhere. Provide the model, serial, tonnage and refrigerant if known. Describe connected systems that remain in service, the likely exit and the facility contact who can review isolation and access.
For a chiller labeled Smardt to sell in Ohio, include the location and a contact who can confirm the asset and arrange site access. If a detail is unavailable, say so instead of taking an unsafe photograph or guessing at the specifications.
Does the owner need to hire a truck?
No. For the agreed purchase, the buyer covers loading, freight and hauling, as well as required disconnects, refrigerant recovery, rigging and crane work. The owner or site representative provides access and identifies the equipment to be sold.
