What to know about used industrial chillers
A surplus chiller can be a single packaged machine or part of a larger central cooling plant. The most useful starting point is not an estimate of scrap weight, but an inventory of the specific equipment offered and the practical route out of the building.
For removal in Geauga County, identify the point where the chiller can be released and the site contact who controls access. The sale includes buyer-paid removal for the agreed scope, so the owner does not need to arrange a truck or remove refrigerant before requesting an offer. The actual path and connections must still be reviewed for safety.
Plan the pickup at your Geauga County site
For pickup in Geauga County, provide the actual site address and service entrance, whether the equipment is in Chardon, the county seat, or elsewhere in the county. The address alone does not show where a truck can stage or where the chiller exits. For a closed or infrequently occupied property, note whether lights, safe access and a site contact are available. A picture of the actual chiller and its surroundings is more useful than an old property listing.
Tell us about known site restrictions before scheduling. A site contact can explain what is accessible, but the removal team must evaluate the actual route, load and work area.
Reconcile original and later labels
Photograph the whole assembly and its manufacturer label, and note whether a starter, drive or control cabinet is attached or separate.
An old equipment schedule, an original nameplate and a later service tag may not all describe the same configuration. Photograph the unit label and any retrofit or conversion markings without removing covers. Supply the model, serial, capacity, voltage and stated refrigerant. If the documents disagree, share the conflict instead of choosing the answer that sounds most likely; the buyer can follow up on the actual equipment.
Condition is information, not a testing requirement
Equipment can be shut down, older, incomplete or of unknown operating status; explain what you know without restarting it.
A prior refrigerant conversion, controller replacement or major repair can change how the machine is identified. An original plate and later service label can both be useful; include the dates or records only if available.
We consider used, surplus and non-running chillers, including equipment of unknown operating condition. There is no need to restore power, repair a fault or perform a performance test to ask for a cash offer. Accurate disclosure and a possible site access review are different from requiring the machine to operate.
Separate the chiller from live plant systems
The buyer coordinates and pays for the agreed disconnects and refrigerant recovery. Before the chiller is released, the facility representative should identify which water circuits, electrical feeds and controls serve other equipment. Qualified personnel plan isolation and recovery for the actual system. A machine that is not running can still contain refrigerant, fluid or stored electrical energy; do not cut, drain or vent it to obtain an offer.
Measure the path from room to truck
For indoor equipment, identify the corridor, doorway and proposed loading area; for outdoor equipment, show the pad, fence and truck approach.
The buyer covers agreed rigging, crane work if needed, loading, freight and hauling. Give the width and height of the narrowest opening, the distance to the loading point and any turns or changes of level. The chiller may have been installed before walls, cables or other equipment were added. A rigging crew verifies actual weight, lifting points and floor capacity; the owner should not try to move the machine for a quote.
Document an as-is purchase
A clear as-is discussion distinguishes known faults from missing information. Provide photographs and describe removed components or an uncertain history; a running test is not required. We consider those facts alongside the removal requirements when making a cash offer. If accepted, payment is upfront before pickup. Confirm the machine, included accessories and buyer-paid scope rather than relying on an informal verbal description.
Where records conflict, share both the installed equipment label and the inventory sheet. The buyer can resolve questions during review rather than assuming that a single old schedule describes the present machine.
What to send for a useful first conversation
When a building is closing, collect the unit identification and current photographs while safe access is available. Record the person authorized to sell, the person who can provide entry after closure, and any known removal constraints. Tell us whether records, controls or components are missing; there is no need to repair or test the machine before asking for an offer.
For a surplus chiller needing removal in Geauga County, include the location and a contact who can confirm the asset and arrange site access. If a detail is unavailable, say so instead of taking an unsafe photograph or guessing at the specifications.
Does cooling tonnage equal equipment weight?
No. Cooling tons measure capacity, not the weight of the assembly. We consider all tonnages, including 20 to 2,000+ tons. A removal crew needs the actual dimensions and verified weight, not an estimate based on the capacity label.
