What to know about used industrial chillers
A surplus chiller can be a single packaged machine or part of a larger central cooling plant. The most useful starting point is not an estimate of scrap weight, but an inventory of the specific equipment offered and the practical route out of the building.
Owners in Clark County can request an offer for one surplus machine or several separately identified units. The actual model, current condition and pickup access matter more than whether the equipment is in a city, an industrial property or an outlying facility. Identify the owner and the machine before assuming adjacent pumps or other assets are part of the sale.
Plan the pickup at your Clark County site
For pickup in Clark County, provide the actual site address and service entrance, whether the equipment is in Springfield, the county seat, or elsewhere in the county. The address alone does not show where a truck can stage or where the chiller exits. If the equipment is indoors, give the floor level, the width and height of the narrowest service opening, and the distance to a place where a truck can load. A corridor photo is often more useful than a photograph of the building front.
Tell us about known site restrictions before scheduling. A site contact can explain what is accessible, but the removal team must evaluate the actual route, load and work area.
Reconcile original and later labels
Photograph the whole assembly and its manufacturer label, and note whether a starter, drive or control cabinet is attached or separate.
An old equipment schedule, an original nameplate and a later service tag may not all describe the same configuration. Photograph the unit label and any retrofit or conversion markings without removing covers. Supply the model, serial, capacity, voltage and stated refrigerant. If the documents disagree, share the conflict instead of choosing the answer that sounds most likely; the buyer can follow up on the actual equipment.
Condition is information, not a testing requirement
Equipment can be shut down, older, incomplete or of unknown operating status; explain what you know without restarting it.
Visible corrosion, coil damage, water staining or missing insulation should be shown in photographs rather than concealed. The buyer can consider the equipment as-is while also planning how its condition affects safe handling.
We consider used, surplus and non-running chillers, including equipment of unknown operating condition. There is no need to restore power, repair a fault or perform a performance test to ask for a cash offer. Accurate disclosure and a possible site access review are different from requiring the machine to operate.
Separate the chiller from live plant systems
The buyer coordinates and pays for the agreed disconnects and refrigerant recovery. Before the chiller is released, the facility representative should identify which water circuits, electrical feeds and controls serve other equipment. Qualified personnel plan isolation and recovery for the actual system. A machine that is not running can still contain refrigerant, fluid or stored electrical energy; do not cut, drain or vent it to obtain an offer.
Measure the path from room to truck
For indoor equipment, identify the corridor, doorway and proposed loading area; for outdoor equipment, show the pad, fence and truck approach.
The buyer covers agreed rigging, crane work if needed, loading, freight and hauling. Give the width and height of the narrowest opening, the distance to the loading point and any turns or changes of level. The chiller may have been installed before walls, cables or other equipment were added. A rigging crew verifies actual weight, lifting points and floor capacity; the owner should not try to move the machine for a quote.
Coordinate a sale with a larger project
A replacement or shutdown may have several contractors working against different milestones. Tell us when the equipment can be released, who approves access and whether shared systems need to stay operational. We make a cash offer and pay upfront before pickup when accepted. Put the asset list and agreed buyer-paid removal work in writing so the chiller purchase is not confused with the entire plant project.
If the chiller is being replaced, tell us when it will actually be released and which plant services must remain live. A replacement schedule and a completed isolation are different things.
What to send for a useful first conversation
Start with an asset list: manufacturer, model, serial, rated capacity, refrigerant and the location of each machine. Identify which units are surplus and whether they are still connected. Add photographs showing the room, pad or roof and the route toward a loading area. If the records are incomplete, mark unknown items rather than guessing or starting the machine.
For used chillers in Clark County, include the location and a contact who can confirm the asset and arrange site access. If a detail is unavailable, say so instead of taking an unsafe photograph or guessing at the specifications.
What if the refrigerant is unknown?
Tell us the refrigerant is unknown and share any original or later labels you can safely photograph. We consider all refrigerants. The buyer coordinates required recovery with qualified personnel; the owner should not open a circuit or release refrigerant to identify it.
