What to know about screw chillers
A screw chiller uses a rotary screw compressor. It may be a packaged outdoor unit or an indoor machine in a larger water system, and a single chiller can have more than one compressor or refrigerant circuit. The actual configuration matters more than the compressor name alone.
For this Hamilton purchase, describe the actual screw chillers offered and distinguish the unit from any shared equipment that remains on site. The offer can include a plan for the buyer to remove it, rather than asking the owner to deliver it or run a test.
Plan the pickup at your Hamilton site
Hamilton is in Butler County. The city of Hamilton is in Butler County; it is not the same location as Hamilton County. Provide the complete address so dispatch and the removal team are directed to the correct site. Describe dock access, door dimensions and whether the chiller is in a shared plant before a route is chosen.
Tell us about known site restrictions before scheduling. A site contact can explain what is accessible, but the removal team must evaluate the actual route, load and work area.
Compare the machine and its electrical gear
Photograph the complete machine, chiller and compressor labels, and the control panel. Specify whether the tonnage is for the whole unit or a single circuit.
Read the manufacturer, complete model and serial number from the chiller itself. Record rated cooling capacity, voltage, phase and the refrigerant on the unit plate if visible. A separate starter or variable-frequency drive can have its own label and may sit in another room. Photograph both and say whether the cabinet is included; a picture of a building automation panel alone does not identify the chiller.
Condition is information, not a testing requirement
A known fault on one circuit, missing electrical parts or a prior repair should be described as accurately as possible; do not energize equipment for the quote.
A machine described as spare may be disconnected, or it may still be connected and held for backup. Clarify its current release status and when the site can make it available; do not start it just to establish its value.
We consider used, surplus and non-running chillers, including equipment of unknown operating condition. There is no need to restore power, repair a fault or perform a performance test to ask for a cash offer. Accurate disclosure and a possible site access review are different from requiring the machine to operate.
Keep an occupied building operating
If the property remains occupied, tell the buyer which cooling services and access routes must remain available. A facility representative should establish the work boundaries before qualified personnel plan the actual disconnect and refrigerant recovery. We coordinate and pay for that work within the agreed purchase scope. The owner does not need to vent, drain or isolate the chiller to request a cash offer.
Protect equipment that stays behind
Show the skid, connections and access around the compressor and vessels so the buyer can plan the disconnect and movement as a complete package or approved sections.
Mark the chiller to be sold and photograph nearby systems that must remain. The route may pass sensitive controls, an occupied area or active machinery. The buyer coordinates and covers agreed rigging, crane if needed, loading and freight; the site representative helps identify operating boundaries and access restrictions. Rigging professionals choose methods after assessing the equipment, lift points and building conditions.
Understand what an offer covers
The offer considers the identifiable equipment and the work needed for the agreed removal. We make a cash offer and, when it is accepted, pay upfront before pickup. Confirm the amount, payment method, included components and buyer-paid removal scope in the transaction documents. Do not assume a separate pump, control cabinet or other nearby asset transfers unless it is specifically listed.
For multiple units, label each nameplate photo to match its location. Decide whether the sale includes all machines as a group or only the ones listed in the offer; nearby pumps and electrical gear are not automatically included.
What to send for a useful first conversation
Start with an asset list: manufacturer, model, serial, rated capacity, refrigerant and the location of each machine. Identify which units are surplus and whether they are still connected. Add photographs showing the room, pad or roof and the route toward a loading area. If the records are incomplete, mark unknown items rather than guessing or starting the machine.
For screw chillers in Hamilton, include the location and a contact who can confirm the asset and arrange site access. If a detail is unavailable, say so instead of taking an unsafe photograph or guessing at the specifications.
Does the owner need to hire a truck?
No. For the agreed purchase, the buyer covers loading, freight and hauling, as well as required disconnects, refrigerant recovery, rigging and crane work. The owner or site representative provides access and identifies the equipment to be sold.
