What to know about Smardt chillers
Some Smardt chillers use oil-free magnetic-bearing compressor technology, but the name alone is not proof of a particular configuration. Explain the installed compressor type where known and provide the machine label so the actual equipment can be evaluated.
A chiller labeled Smardt in Dayton may be surplus after a plant upgrade, building closure or cooling-system replacement. Identify the exact machine rather than the entire plant, and specify whether the starter or drive is part of the proposed purchase.
Plan the pickup at your Dayton site
Dayton is in Montgomery County. For a Dayton-area chiller, tell us whether pickup is from an active campus, an industrial building or a property being vacated. A site plan that marks the mechanical room, service exit and possible truck position can clarify the work. Do not assume a loading dock is suitable without sharing its height and available clearance.
Tell us about known site restrictions before scheduling. A site contact can explain what is accessible, but the removal team must evaluate the actual route, load and work area.
Reconcile original and later labels
Photograph the complete unit, its model and serial label, individual compressor labels if safely visible, and the controller or separate power cabinet.
An old equipment schedule, an original nameplate and a later service tag may not all describe the same configuration. Photograph the unit label and any retrofit or conversion markings without removing covers. Supply the model, serial, capacity, voltage and stated refrigerant. If the documents disagree, share the conflict instead of choosing the answer that sounds most likely; the buyer can follow up on the actual equipment.
Condition is information, not a testing requirement
Mention disconnected controls, a compressor issue or service history only if known. An unknown fault does not require a test or an attempt to reset the machine.
A long idle period can leave the maintenance history incomplete. Give the last known status and distinguish what you observed from what an old record says. An unreadable label or an unknown fault is better described honestly than filled in with a guess.
We consider used, surplus and non-running chillers, including equipment of unknown operating condition. There is no need to restore power, repair a fault or perform a performance test to ask for a cash offer. Accurate disclosure and a possible site access review are different from requiring the machine to operate.
Identify the actual refrigerant safely
We consider all refrigerants and arrange qualified recovery when required as part of the agreed purchase. Photograph the original nameplate and any current conversion label, and pass along prior recovery records if available. A switched-off machine is not necessarily empty. Do not open a fitting or release refrigerant to check it. Appropriate personnel must assess the actual charge, circuit and applicable handling requirements.
Check loading space and truck access
Identify the heat exchangers, compressor mounting and power connections in photographs; the removal crew will determine safe lifting points and handling.
A suitable loading area requires more than a nearby door. Describe the gate, turning room, dock height, possible truck position and any other contractors using the area. The buyer handles and covers the agreed rigging, crane work if needed, loading, freight and hauling. Weight, load distribution and the route to the vehicle must be verified for the particular machine and property.
Understand what an offer covers
The offer considers the identifiable equipment and the work needed for the agreed removal. We make a cash offer and, when it is accepted, pay upfront before pickup. Confirm the amount, payment method, included components and buyer-paid removal scope in the transaction documents. Do not assume a separate pump, control cabinet or other nearby asset transfers unless it is specifically listed.
If the chiller is being replaced, tell us when it will actually be released and which plant services must remain live. A replacement schedule and a completed isolation are different things.
What to send for a useful first conversation
For a restricted property, explain who authorizes access and whether the machine can be visited or photographed safely. Provide the available nameplate data and a view of the chiller and its surroundings. Note any access controls, active neighboring equipment and expected release conditions. The buyer needs these facts to plan removal, not a performance demonstration.
For a chiller labeled Smardt in Dayton, include the location and a contact who can confirm the asset and arrange site access. If a detail is unavailable, say so instead of taking an unsafe photograph or guessing at the specifications.
Does cooling tonnage equal equipment weight?
No. Cooling tons measure capacity, not the weight of the assembly. We consider all tonnages, including 20 to 2,000+ tons. A removal crew needs the actual dimensions and verified weight, not an estimate based on the capacity label.
